|
INDUSTRIAL DUTY FIBERGLASS SHELTERS
For Highly Corrosive & Marine Locations
Shelter Application
Our Industrial Duty Fiberglass Shelters are intended for
Chemical Processing or Waste water treatment areas where
corrosive vapors such as Hydrogen Sulfide or Chlorine
are present and offshore or coastal areas where
salt-laden air or saltwater spray is prevalent. Beyond
corrosion resistance, the coating material utilized
includes a glass fiber reinforced Class1 flame-retardant
resin and UV resistance gel coating that is available in
a variety of colors.
Construction Method
Shelter Wall
Rib frame is fabricated of 80mm x 80mm x 3mm and 50mm x
50mm x 2mm metal tubes and then filled with Polyurethane
foam insulation. The inner and outer surfaces shall
receive a spray coating of catalyst and resin based Gel
and chop-sprayed glass fibers. Material shall then be
roller pressed to remove all trapped air and embed all
fibers within the coating strata. The Exterior shall
then be lightly sanded, utilizing a combination of soft
pad side grinders and orbital sanders to obtain a smooth
finish and free of any visible blemishes or raised
fibers.
The surface shall receive a Flame-retardant Resin and
Maine Grade UV Resistant Gel Coating Materials.
Shelter Roof
Roof frame is made of 50mm x 50mm x 3mm Metal Tubes and
then filled with Polyurethane foam insulation. Top and
bottom cover of the roof would be made of 6mm thick
smooth GRP.
For applications where climate is severe, slope of 4
inches per foot (4/12) is provided suitable for heavy
rain or snow.
The surface shall receive a Flame-retardant Resin and
Maine Grade UV Resistant Gel Coating Materials.
Shelter Flooring
Bottom steel frame would be made of 80mm x 80mm x 3mm
profiles. Over that a layer of 1.5mm thick Polyester
Resin Lamination, 18mm thick BWP Grade Plywood and 4mm
thick White Vinyl Tiles would be fixed respectively.
Door
One piece made of Resin Transfer Molded in matched metal
molds, smooth finished, seamless, monolithic, warp-free
composite consisting of gel-coat, fiberglass
reinforcement, polyester resin, insulating core and
internal reinforcements with all mortises, openings,
recesses and pockets molded in place as required.
Size:
30” x 70”
Weather strip:
Neoprene sponge rubber bulb type gasket with flexible
lock to retain permanent grip.
Type:
Sweep door.
Latch:
Single pointed keyed Stainless steel cylindrical latch.
Door Closer:
Hydraulic.
Finish
The surface shall receive a Flame-retardant Resin and
Maine Grade UV Resistant Gel Coating Materials.
Exterior Finish:
Fiberglass Exterior Natural Suede. Gel coat with low
luster finish, smooth and free from fiber pattern,
roughness or other irregularities.
Interior Finish:
FRB over insulation. 1/8” thick chemically bonded to
Gel coat white in color.
Accessories
Mechanical
1.
Air conditioner 24000 BTU Hot and Cool. Single Phase: 1
ea.
2.
12 Port Entry Panel: 1 ea.
3.
18” width and up to 10’ Cable Rack Assembly: 1 ea.
4.
, Single Phase, 50
Electrical
1.
Electrical Panel Board – 200 AMP Single Phase 50/60Hz:
1 ea.
2.
¼” x 4” x 24” Ground Bars: 2 ea.
3.
Halo Ground System: 1 ea.
4.
4’ long Fluorescent light inside the shelter: 1 ea.
5.
13 Amp Switched Twin Socket mounted inside on walls: 6
ea.
6.
GFI Socket mounted out side: 1 ea.
Sensors & Alarms Alarm
1.
Smoke Detector: 1 ea.
2.
Temperature Difference Detector: 1 ea.
3.
Open Door Alarm: 1 ea.
4.
Power Failure Alarm: 1 ea.
5.
Motion Detector switched inside next to Door: 1 ea.
Packing
All shelters would be wrapped in LDPF sheets to protect
during transporting. Store products on flat Surface and
protect from construction traffic and damage.
Installation
Verify that the concrete pad is free of debris, level,
true to plane and of correct dimensions to receive the
structure. Correct all deficiencies before proceeding.
UP ARMOR INSTALLATION & REFURBISH PROGRAM
Introduction
ALMC Armor Installation and Refurbishing programs are
among the best in the SWA area. ALMC is one of the
lead contract supply and services providers for
multinational military missions.
Our 100 plus expats are well trained, and experienced
professionals in repairing and refurbishing military
equipment. ALMC experienced professionals can be at any
service location in Kuwait, Afghanistan and Iraq as
prime or in support of any company already at location.
ALMC delivers specialized services in the following
areas:
::
Armor Installation (AOA)
::
Hummv 2 Door, 4-Door, Refurbish and Repair (M (939,
M969)
::
Air Conditioning System (Installation & Repair)
::
Compressor System
::
Generators – (All Sizes)
::
Wiring Harness
::
Perform Inspection for front line completion
::
M1 Abrams
::
M2 Bradley
::
M 992 Ammo Carrier
::
M 109 Howitzer
::
M 113’s
::
2.5 Ton Trucks
::
5 Ton Trucks
|
